- 您现在的位置：买卖IC网 > Sheet目录316 > BD8112EFV-ME2 (Rohm Semiconductor)IC LED DRIVER 24-VSSOP
BD8112EFV-M
Technical Note
● 5V voltage reference (VREG)
5V (Typ.) is generated from the VCC input voltage when the enable pin is set high. This voltage is used to power internal
circuitry, as well as the voltage source for device pins that need to be fixed to a logical HIGH. UVLO protection is integrated
into the VREG pin. The voltage regulation circuitry operates uninterrupted for output voltages higher than 4.45 V (Typ.),
but if output voltage drops to 4.3 V (Typ.) or lower, UVLO engages and turns the IC off. Connect a capacitor (Creg = 2.2μF
Typ.) to the VREG terminal for phase compensation. Operation may become unstable if Creg is not connected.
● Constant-current LED drivers
If less than four constant-current drivers are used, unused channels should be switched off via the LEDEN pin configuration.
The truth table for these pins is shown below. If a driver output is enabled but not used (i.e. left open), the IC’s open
circuit-detection circuitry will operate.
Please keep the unused pins open. The LEDEN terminals are pulled down internally
in the IC, so if left open, the IC will recognize them as logic LO. However, they should be connected directly to VREG or
fixed to a logic HI when in use.
LED
LED EN
1
2
L
H
ON
ON
ON
OFF
? Output current setting
LED current is computed via the following equation:
I LED = min[VDAC , VISET(=2.0V)] / RSET x GAIN [A]
(min[VDAC , 2.0V] = the smaller value of either VDAC or VISET; GAIN = set by internal circuitry.)
In applications where an external signal is used for output current control, a control voltage in the range of 0.0 to 2.0 V
can be connected on the VDAC pin to control according to the above equation. If an external control signal is not used,
connect the VDAC pin to VREG (do not leave the pin open as this may cause the IC to malfunction). Also, do not switch
individual channels on or off via the LEDEN pin while operating in PWM mode.
The following diagram illustrates the relation between ILED and GAIN.
ILED vs GAIN
3150
3100
3050
3000
2950
2900
2850
0
20
40
60
80
100
120
140
160
ILED[mA]
In PWM intensity control mode, the ON/OFF state of each current driver is controlled directly by the input signal on the
PWM pin; thus, the duty ratio of the input signal on the PWM pin equals the duty ratio of the LED current. When not
controlling intensity via PWM, fix the PWM terminal to a high voltage (100%). Output light intensity is greatest at 100%
input.
PWM
ILED(50mA/div)
PWM
ILED
PWM=150Hz
Duty=0.
PWM=150Hz
Duty=50%
www.rohm.com
? 2010 ROHM Co., Ltd. All rights reserved.
7/22
2011.08 - Rev.C
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
BD8119FM-ME2
IC WHITE LED DVR PWM 28-HSOP
BD82103GWL-E2
IC LED DRVR WHITE BCKLGT 11-UCSP
BD9206EFV-E2
IC LED DRIVER 6V LCD 20HTSSOP
BD9207FPS-E2
IC LED DVR STEPDWN 1.5A TO252S-5
BH-14E_TI-20T_CTI
ADAPTER PIN CONVERTER 14-20 PIN
BH-20E_CTI-60T_TI
ADAPTER PIN CONVERTER 20-60 PIN
BH-ADP-ISO20
ISOLATION ADAPTER 20-PIN TI JTAG
BH-GANG2000
GANG2000 PROGRAMMER TI 32BIT MCU
相关代理商/技术参数
BD8113EFV
制造商:ROHM 制造商全称:Rohm 功能描述:White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type)
BD8113EFV_11
制造商:ROHM 制造商全称:Rohm 功能描述:White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type)
BD8113EFV-E2
功能描述:LED照明驱动器 IC LED DRIVER RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
BD8115F-M
制造商:ROHM 制造商全称:Rohm 功能描述:LED Driver IC
BD8115F-MTE2
功能描述:LED照明驱动器 Auto Grade LED Drvr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
BD8115FP-MTE2
制造商:ROHM 制造商全称:Rohm 功能描述:LED Driver IC
BD8115HFP-MTTR
制造商:ROHM 制造商全称:Rohm 功能描述:LED Driver IC
BD8118FM
制造商:ROHM 制造商全称:Rohm 功能描述:Silicon Monolithic Integrated Circuit